Jump to content

Share Our Forum With Your Friends!

Tim Osborne

Member
  • Content count

    32
  • Joined

  • Last visited

About Tim Osborne

  • Rank
    Advanced Member
  • Birthday 30/04/1966

Personal Information

  • Cleaning Method
    Water Fed Pole & Tradtitional
  • When did you start window cleaning?
    April 2014
  • Location
    Ireland

Recent Profile Visitors

The recent visitors block is disabled and is not being shown to other users.

  1. Tim Osborne

    Add Hot Water to WFP Trolley??

    That looks promising I will have to investigate that a bit. Yes like you said I was a bit concerned about putting that other heater in the 25ltr tank.
  2. Tim Osborne

    Add Hot Water to WFP Trolley??

    Thanks Nudel I was thinking along the lines of your solution B the electric heater. I was thinking of something that would heat water on demand only when needed. I have seen these on ebay https://www.ebay.co.uk/itm/220V-2500W-Water-Heater-Element-Portable-Electric-Immersion-Boiler-Heating-Rod/173096459971?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2060353.m1438.l2649 These could be placed into 25ltr tank to heat when needed.
  3. Does anyone have any tips on adding water heater to a wfp trolley? Thanks for any advise.
  4. Tim Osborne

    Old protective tape on window frames!!!

    Thanks all for your suggestions I think I will try the heat gun first and see what it does. Either way I think I'm in for a long day!!
  5. Tim Osborne

    Old protective tape on window frames!!!

    sorry no I didn't take any.
  6. Does anyone have any tips for removing the protective tape on window frames? The stuff I have to remove is on patio doors and has been there for about 2 years baking in the sun. When I peal it off it comes off in small chunks! Thanks for your help.
  7. Good to know...thanks for tip
  8. Thanks for advice I found a great PDF describing switches. SPST, SPDT, and DPDT Switches Demystified.pdf
  9. Thanks for your reply. Do you think a switch like this on ebay would work https://www.ebay.co.uk/itm/261513977084?var=560391577652
  10. Is the SPDT switch you use in the diagram an "on-off-on" type or just a on-off type? Thanks
  11. Tim Osborne

    Excelerator Handle

    Update on handle- I contacted Moreman about the problem and they got me in contact with Robert Hatt AKA Polzn Blades and he said to check the spring. On the prototypes they used a different spring that is now on the Excelerators in production. Somehow I got a prototype spring in mine and was rusted and weak. Moreman had a new handle sent to me and it is fantastic. I am very impressed with Moreman and there customer support. I take back everything I said about the handle! This is a great handle and has save me loads of time and money.
  12. Tim Osborne

    Excelerator Handle

    Not dropped it yet but I do use it with the FLIQ pad and have noticed the rubber and channel have moved quite a bit after using the FLIQ. Don't get me wrong, I love this squeegee it is by far the best yet but I am a bit concerned with the movement of the channel and rubber after only a few weeks of use. The quality is just not there for a handle that cost nearly 20 euro!
  13. Tim Osborne

    Excelerator Handle

    I have been using the Excelerator for a few weeks and already the channel (liquidator 2) slides around very easily in the handle. Does anyone else find that this is happening? It seems the spring inside is not strong enough on mine. Maybe its defective??
  14. I do like these handles and I like the ability to use the swivel option, I use that all the time. But over a short time the 4 little plastic knurls that lock it wear down and then it swivels when not wanted. I also like to set it to 0 deg for some work. Those new handles look like they may be good option the replace these..lets hope
×

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.