Water reading 007

[Shaun1977]

Is it ok to use water at reading of 007

---

I am here: http://tapatalk.com/map.php?zs2nqv

 

[chip]

yes, but most try to keep below 5.

 

[Matty H]

Is it ok to use water at reading of 007

---

I am here: http://tapatalk.com/map.php?zs2nqv

Run it through some resin mate bring it down. I'm a stickler though never go above 2 - 3.

I could ask Miss Moneypenny for you??? Sorry couldn't resist /emoticons/biggrin.png

 

[James]

5 and below I think is best.

---

I am here: http://tapatalk.com/map.php?m3wm4n

 

[Shaun1977]

Badbusdriver do you get no spotting

 

[simon]

ive always changed about 12 with no problems but just for the crack im going outside to do my house with tap water - 36ppm, its minging so it'll be like a first clean - i'll let you know the results later

 

[James]

36ppm? Welcome to the land of spotting! Depends how dirty your windows are though.

---

I am here: http://tapatalk.com/map.php?sedecm

 

[simon]

well thats done but its getting dark so i cant really tell, ill know tomorrow prob, but the power was awsome, i only use a backpack & ive never seen a surflo pump at work so i dont know how strong their jet is but straight from the tap just hammered the frames clean -

 

[James]

What psi is it buddy? 100?

---

I am here: http://tapatalk.com/map.php?kjar1q

 

[chip]

i've cleaned the french doors on my garage (don't ask) with 200 ppm tapwater and only got spots round the edges where it beads, but the part that sheets-spotless! but on my patio door which totally beads it was a shambles. make of that what you will, no one seemed to care in the vip lounge /emoticons/smile.png

 

[simon]

my backpacks 70 psi & i use it on the slowest speed - it has 3 - i was always told glass that beads needs more rinsing than glass that sheets, but to be honest im starting to think its getting the frames clean thats the key to fast & good cleaning

 

[chip]

there's a few variables, but largely i agree with you, what you can get away with, ie do quicker depends on the quality of the glass and the cleaness of the top frame, if you happen to catch it

 

[simon]

well ive started using a flat trim sill brush & its much stiffer than the medium dual trim i was using so it cleans the whole frame well & quickly & ive noticed im spending a lot less time on the glass itself as i know the frames are clean so wont drip - i do the full frame not just tops

 

[chip]

yes, i was just saying top frame with reference to dirt dripping down glass, not an issue with sides so does'nt need any kind of attention to detail

 

[Shaun1977]

Simon are sill brushes ok for doing full windows mate I just ask as Iv never used thm

---

I am here: http://tapatalk.com/map.php?qk0npr

 

[simon]

shaun 1977 i think they're the dogs b's, i think its the only brush i need - i did the van with it today & its great. they're good for difficult corners & very light as well & those finials on top of conservatories

chip - i said that cos i splash everything the way i work (clumsy) so i need it all clean

working with a ppm of 36 well my windows weren't bad at all, i wouldn't work at that ppm, but i suppose if i was stuck it would be ok -

 

[Richard]

007 should be ok,

What you have to be careful with is if the TDS is over 000 for any length of time and exposed to sunlight you can start to grow the green algae in your water containers or tank if they are opaque or clear.

Richard