Jump to content

Don't want to see ads? Become a subscribed member.

speed and water


chip

Recommended Posts

some time back i did an experiment, even drew up an algebraic formula but can't find it.

anyhow, i set the pump to a low flow and cleaned a window to my satisfaction and timed it and worked out the water usage. did the exact same experiment with a higher flow, and it worked out i cleaned the window faster and used less water! about 10% i think it was. obviously there's a few variables to consider, my opinion of satisfactorily rinsed might not be yours but that' basically irrelevant. what is relevant is how fast you can physically wash a window, a slow worker will waste water, a fast worker will waste time, and of coarse whether you turn off between windows, etc.

still, i think there's a potential to increase speed and save water

Link to comment

This is very interesting Chip! I find If I set my pressue at around 15 & work quickly I normally will save water than if I say set the pressure at around 30-35. But I guess everyones different. I'd be interested to see this formula you have created!

 

James.

Link to comment

what it boils down to, mainly, is the rinse. if you're like me if the waters coming out slow, you'll move the brush to and fro slowly and try to hit every bit of the window, if it's coming with a bit of force, you can be rinsed in no time and as the water is running down the window like a torrent, you have more confidence that it's all rinsed, if you get my drift.

Link to comment

Forget flow controllers! turn your pump up as high as it can go!

 

You will as you say chip will not use any more water as you can clean faster! trying to save water slows you down! (the higher the flow the faster you go!):)

Link to comment

Screw pencil jets, fan jets are the way forward! Apparantly a friend of mine said there is no need for rinsing at the end of the clean as if your waters on 0ppm it will dry naturally.

 

My argument was the rinsing gets rid of any bits and pieces (dried cobwebs etc) and leaves a perfect finish. He says otherwise.

 

James.

Link to comment

in theory i don't think it's usually nescessary- if the flows high enough you've got water rinsing while washing. in practice i'm in your camp james, have to rinse!

exception being if it's to awkward to, in that case i wash the window and then run it across the top of the glass a couple of times.

i don't have flow controller either james, can't see the point just alter the pump accordingly. think you need a by-pass though, not sure.

Link to comment

I have fan jets and always rinse, one thing you can do over pencils is rinse on the glass, this is very handy when doing windows at height.

 

Yes, deffinately agree, big advantage when doing windows at 3 storey height!

 

James

Link to comment

been through the archives and dug out the equation (just for you james)

 

L/60xT which is to say litres per min diveded by seconds per min multiplied by time taken.

 

my experiment went thus:

slow flow 800 ltrs per min, so

800/60=1.333r ltrs per sec

1.333rx12 (seconds taken) =1.5999r liters used

 

higher flow

1200/60= 20 ltrs per sec

20x7 (seconds taken) =140 or 1.4 ml to clean it.

Link to comment

been through the archives and dug out the equation (just for you james)

 

L/60xT which is to say litres per min diveded by seconds per min multiplied by time taken.

 

my experiment went thus:

slow flow 800 ltrs per min, so

800/60=1.333r ltrs per sec

1.333rx12 (seconds taken) =1.5999r liters used

 

higher flow

1200/60= 20 ltrs per sec

20x7 (seconds taken) =140 or 1.4 ml to clean it.

 

Very impressive chip!

 

I'm going to use this equation to do my own little experiment :D I'll post you my results.

 

James.

Link to comment

Forget flow controllers! turn your pump up as high as it can go!

 

You will as you say chip will not use any more water as you can clean faster! trying to save water slows you down! (the higher the flow the faster you go!):)

Dont' agree.

Pressure controllers let you work in efficient way, not all time you need to blow pump with full of its speed.

Link to comment

?????? i've only had pencil jets & i always have rinsed on the glass i was told it depended whether your brush is flocked (off) or unflocked (on) but ive no idea what my first 2 brushes were & they were always ok but i use a backpack dunno if that has a different flow

Link to comment

your right if you use fan jets with a flocked and rinse on the glass you could be head for trouble as the flock brush tends to hold the dirt

I have my pump on flat out but i use a 60 m hose and was told that the pumps work best when run flat out could be wrong but my pump is over 18 months old with no worry about the controller playing up

 

rinsing on the glass is the way to go as long as you use right brush and can be confident the brush isnt holding dirt.

Link to comment

Just out of interest. If anyone uses Gardiners Medium Dual Trim Sill brush, does it hold dirt, spider webs, etc. I've noticed mine is starting to hold quite abit of dirt. Is it when the bristles start to wear/flare out?

 

James.

Link to comment
  • 1 month later...

‘Static’ water of 1 litre will cover approximately 1 square metre of glass

 

A typical residential window pane of 18”x 36” (aprox 40% of a sq metre) won’t necessarily need 400ml of water to clean (aprox 12 seconds cleaning time, with 2lt per min)

 

‘Active’ flow rate of just over 2 litres a minute will give you 34 millilitres of water per second (about a cupful 250ml of water every 7 seconds) which can be more than enough water to clean 18”x 36” window that is maintained regular

 

The final rinse won’t and shouldn’t always be necessary on every pane of glass you clean. Glass type has very little to do with the final cleaning results,

 

Match water flow rate to your speed of working, adjust flow rate up or down accordingly to match your speed so you either don’t waste water or valuable time.

 

Choice of wfp equipment is important and this does affect final cleaning times; differences in times will be substantial at the extremes, the knock on effects to this can be dramatic for a business.

 

Richard

Link to comment

Jesus you guys are to intellectual for me with all these equations, my equation is 1xdirty window add water approx-just enough until clean = happy customer = me paid :huh: that took a while to cum up with but I think I've got it

Link to comment

Don't want to see ads? Become a subscribed member.


Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.

Ad Blocker Detected

Please disable your ad blocker

Our forum relies on ads to pay for the servers and our time maintaining and running the forum.

Sadly running a forum like this is not free, and due to our popularity, we need servers that can handle the amount of traffic and resources our forum uses.

 

If you do not wish to see ads on our site, please consider supporting the forum with a membership subscription.

 

Accept